Не получается добавить устройство в observium
При попытке добавить устройство, ошибка:
Try to add 172.16.8.251:
Trying v2c community *** [0] ...
No reply on given community *** using v2c.
Could not reach 172.16.8.251 with given SNMP parameters using v2c.
Devices failed: 1.
При этом пинг с сервера observium проходит идеально, при попытке snmpwalk вылетает timeout no response.
Вот код snmpd.conf на добавляемом устройстве:
#
# snmpd.conf:
# An example configuration file for configuring the ucd-snmp snmpd agent.
#
####
# First, map the community name "public" into a "security name"
# sec.name source community
com2sec notConfigUser default commavt24311
####
# Second, map the security name into a group name:
# groupName securityModel securityName
group notConfigGroup v1 notConfigUser
group notConfigGroup v2c notConfigUser
####
# Third, create a view for us to let the group have rights to:
# Make at least snmpwalk -v 1 localhost -c public system fast again.
# name incl/excl subtree mask(optional)
view systemview included /.1.3.6.1.2.1.1
view systemview included .1.3.6.1.2.1.25.1.1
####
# Finally, grant the group read-only access to the systemview view.
# group context sec.model sec.level prefix read write notif
access notConfigGroup "" any noauth exact systemview none none
# -----------------------------------------------------------------------------
# Here is a commented out example configuration that allows less
# restrictive access.
# YOU SHOULD CHANGE THE "COMMUNITY" TOKEN BELOW TO A NEW KEYWORD ONLY
# KNOWN AT YOUR SITE. YOU *MUST* CHANGE THE NETWORK TOKEN BELOW TO
# SOMETHING REFLECTING YOUR LOCAL NETWORK ADDRESS SPACE.
## sec.name source community
#com2sec local localhost COMMUNITY
#com2sec mynetwork NETWORK/24 COMMUNITY
## group.name sec.model sec.name
#group MyRWGroup any local
#group MyROGroup any mynetwork
#
#group MyRWGroup any otherv3user
#...
## incl/excl subtree mask
#view all included .1 80
## -or just the mib2 tree-
#view mib2 included .iso.org.dod.internet.mgmt.mib-2 fc
## context sec.model sec.level prefix read write notif
#access MyROGroup "" any noauth 0 all none none
#access MyRWGroup "" any noauth 0 all all all
###############################################################################
# Sample configuration to make net-snmpd RFC 1213.
# Unfortunately v1 and v2c don't allow any user based authentification, so
# opening up the default config is not an option from a security point.
#
# WARNING: If you uncomment the following lines you allow write access to your
# snmpd daemon from any source! To avoid this use different names for your
# community or split out the write access to a different community and
# restrict it to your local network.
# Also remember to comment the syslocation and syscontact parameters later as
# otherwise they are still read only (see FAQ for net-snmp).
#
# First, map the community name "public" into a "security name"
# sec.name source community
#com2sec notConfigUser default public
# Second, map the security name into a group name:
# groupName securityModel securityName
#group notConfigGroup v1 notConfigUser
#group notConfigGroup v2c notConfigUser
# Third, create a view for us to let the group have rights to:
# Open up the whole tree for ro, make the RFC 1213 required ones rw.
# name incl/excl subtree mask(optional)
#view roview included .1
#view rwview included system.sysContact
#view rwview included system.sysName
#view rwview included system.sysLocation
#view rwview included interfaces.ifTable.ifEntry.ifAdminStatus
#view rwview included at.atTable.atEntry.atPhysAddress
#view rwview included at.atTable.atEntry.atNetAddress
#view rwview included ip.ipForwarding
#view rwview included ip.ipDefaultTTL
#view rwview included ip.ipRouteTable.ipRouteEntry.ipRouteDest
#view rwview included ip.ipRouteTable.ipRouteEntry.ipRouteIfIndex
#view rwview included ip.ipRouteTable.ipRouteEntry.ipRouteMetric1
#view rwview included ip.ipRouteTable.ipRouteEntry.ipRouteMetric2
#view rwview included ip.ipRouteTable.ipRouteEntry.ipRouteMetric3
#view rwview included ip.ipRouteTable.ipRouteEntry.ipRouteMetric4
#view rwview included ip.ipRouteTable.ipRouteEntry.ipRouteType
#view rwview included ip.ipRouteTable.ipRouteEntry.ipRouteAge
#view rwview included ip.ipRouteTable.ipRouteEntry.ipRouteMask
#view rwview included ip.ipRouteTable.ipRouteEntry.ipRouteMetric5
#view rwview included ip.ipNetToMediaTable.ipNetToMediaEntry.ipNetToMediaIfIndex
#view rwview included ip.ipNetToMediaTable.ipNetToMediaEntry.ipNetToMediaPhysAddress
#view rwview included ip.ipNetToMediaTable.ipNetToMediaEntry.ipNetToMediaNetAddress
#view rwview included ip.ipNetToMediaTable.ipNetToMediaEntry.ipNetToMediaType
#view rwview included tcp.tcpConnTable.tcpConnEntry.tcpConnState
#view rwview included egp.egpNeighTable.egpNeighEntry.egpNeighEventTrigger
#view rwview included snmp.snmpEnableAuthenTraps
# Finally, grant the group read-only access to the systemview view.
# group context sec.model sec.level prefix read write notif
#access notConfigGroup "" any noauth exact roview rwview none
###############################################################################
# System contact information
#
# It is also possible to set the sysContact andsysLocation system
# variables through the snmpd.conf file:
syslocation VII-320
syscontact AVT-243, K.E.I O.N.A.
# Example output of snmpwalk:
# % snmpwalk -v 1 localhost -c public system
# system.sysDescr.0 = "SunOS name sun4c"
# system.sysObjectID.0 = OID: enterprises.ucdavis.ucdSnmpAgent.sunos4
# system.sysUpTime.0 = Timeticks: (595637548) 68 days, 22:32:55
# system.sysContact.0 = "Me <[email protected]>"
# system.sysName.0 = "name"
# system.sysLocation.0 = "Right here, right now."
# system.sysServices.0 = 72
###############################################################################
# Logging
#
# We do not want annoying "Connection from UDP: " messages in syslog.
# If the following option is commented out, snmpd will print each incoming
# connection, which can be useful for debugging.
dontLogTCPWrappersConnects yes
# -----------------------------------------------------------------------------
###############################################################################
# Process checks.
#
# The following are examples of how to use the agent to check for
# processes running on the host. The syntax looks something like:
#
# proc NAME [MAX=0] [MIN=0]
#
# NAME: the name of the process to check for. It must match
# exactly (ie, http will not find httpd processes).
# MAX: the maximum number allowed to be running. Defaults to 0.
# MIN: the minimum number to be running. Defaults to 0.
#
# Examples (commented out by default):
#
# Make sure mountd is running
#proc mountd
# Make sure there are no more than 4 ntalkds running, but 0 is ok too.
#proc ntalkd 4
# Make sure at least one sendmail, but less than or equal to 10 are running.
#proc sendmail 10 1
# First, map the community name "public" into a "security name"
# sec.name source community
com2sec notConfigUser default public
####
# Second, map the security name into a group name:
# groupName securityModel securityName
group notConfigGroup v1 notConfigUser
group notConfigGroup v2c notConfigUser
####
# Third, create a view for us to let the group have rights to:
# Make at least snmpwalk -v 1 localhost -c public system fast again.
# name incl/excl subtree mask(optional)
view systemview included /.1.3.6.1.2.1.1
view systemview included .1.3.6.1.2.1.25.1.1
#
#
# See the snmpd.conf manual page, and the output of "snmpd -
rocommunity public 0.0.0.0/0
agentAddress udp:161
syslocation "Server Room"
syscontact Admin <[email protected]>
view systemview included .1.3.6.1.2.1
view systemview included .1.3.6.1.4.1```